Dl360 Gen8 Driver For Mac

2020. 1. 28. 07:07카테고리 없음

Dl360 Gen8 Driver For Mac
  1. Dl360 Gen8 Driver For Mac Mac
  2. Hp Dl360p Drivers
  3. Dl360 Gen8 Driver For Mac Windows 10

Just bought 2 new Proliant DL360 G8's Trying to install MS Server 2012R2 & having issues getting the servers to work The OS installs no problem but after a reboot or two, it won't work anymore. The Server 2012 startup logo appears & then you get a light blue screen (not BSOD) indicating Server 2012 has encountered a problem & cannot load & reboots AHCI SATA Controller - V0.84 B320i Storage Array - V5.54, HBA Firmware 15.10.05.00, ROM Ver 07.25.05.00 Do I need a upgrade or downgrade in some firmware? There must be someone who has had sucess installing Server 2012R2 on one of these models Been fighting this for a few days now Any Help appreciated. Some of the basic Windows startup troubleshooting techniques might get you pointed in the right direction. Hit F8 when Windows is starting up so you can select some options there, like not auto-rebooting, or to debug the startup.

Dl360 Gen8 Driver For Mac Mac

Homelab HP ProLiant DL360p Gen8 VMware stability issues. We were ever-greening our vmware cluster servers at the office and I got my hands on an HP ProLiant DL360p Gen8 server (2x CPU E5-2670, 192GB DDR3) to replace my Xeon E3-1230 supermicro build in my homelab. There is an issue with the ESXi iLO driver which causes PSODs.

Hopefully you'll be able to see the error message or the specific driver it was loading when it had a problem. You could also try a safe boot in case it's some other program or driver doing something.

For

As the above post suggests, make sure you have the latest drivers for everything. I've only used the P420 controllers on the Gen8 boxes which work fine, so I don't know if there's anything specific to the Bxxx models to look out for. I saw someone mention making sure it's set to AHCI mode in the ROM setup, but other than that, I have no idea.:). None of that works I updated all the firmware on the servers Did the OS install from DVD boot & used the suggested Smart Array Driver driver One server was able to boot several times but after being powered off for an hr or so, would not boot into Windows. Just would get the Server2012 logo & then blue/teal screen as before The other server took 4 tries to get the OS to boot without blue screen & only lasted 2 more restarts before again blue screening Getting very tempted to send the servers back.

Hp Dl360p Drivers

You might try doing the intelligent provisioning to install Windows. It should make sure any boot drivers are installed. I don't use the intelligent provisioning myself, but it seems like it's the equivalent of the old Smartstart setup method. It's just built into the server now, no need to boot off a separate CD. On my DL380p Gen8 servers with a P420i and add-on P420 controller, I'm able to boot off a Windows Server 2012 R2 DVD and install it directly without any issues, so I think you're on the right trail with the B320i controller not being detected correctly when using the default driver from Microsoft. Instead of using the intelligent provision install, you could also boot from the Windows disk and go through the steps to install a custom storage driver.

Grab the latest B320i drivers from the HP downloads and use those. Intelligent Provisioning install seems easier though.

Mixed results trying to get the servers to run. Didn't matter if you used the Intelligent Provisioning or a standard install to try & get the OS to boot after install. Managed to get them to boot after OS install after many attempts. Ran the latest Proliant service pack & it updated all the firmware & latest drivers Could get them to reboot 5-7times & things were looking hopeful but that was dashed & the blue screen would appear. Would get the same message as before if you did an F8 & select no auto reboot PAGE FAULT IN NONPAGED AREA (libsa.sys) That file is part of the driver for the array.

Drivers

I am using the latest - ver 62.10.0.64 After several attempts at a restart, you would get the auto repair screen but it appeared not to be able to see the array Wasted 10+days trying to get these blasted servers running. Hi, I am also facing same issues with recently, I followed the below steps.

Its easily installed OS. Reboot the server & get into BIOS using F9 key. Select System Configuration & press enter. 3.Then slect BIOS/Platform Configuration.

Dl360 Gen8 Driver For Mac Windows 10

4.Select Boot options 5.Select Boot Mode. 6.Select Legacy BIOS mode. 7 Select UEFI Optimized Boot & disable it.

8.Again come back to System Options & select USB Boot options & removable flash media boot sequence & USB as first boot option 9.Now save, reboot and start the installation Easily resolve the issues.

Dl360 Gen8 Driver For Mac